Heat exchange falling
Increasing energy consumption and higher process temperature usually begin with hardness and sludge build-up.
Services / Water Analysis
We're testing water. before installation failure.
Industrial water analysis helps to quickly see if the installation works stable. The result is translated into specific decisions for boiler rooms, refrigeration and RO.
When it is worth examining water
The symptoms in the installation can be seen first in the water.
Analysis makes sense when answering a technical question. Therefore, we always start with symptoms and working conditions, and then select the range of measurements.
scale
rust, dents and dirty condensate
Iron in the water and off-range reactions indicate corrosion before leakage occurs.
Unstable circulation
Variable conductivity and salinity make it difficult to maintain repeatable process parameters.
Increasing water and sewage consumption
Too careful blowdown increases media costs, although it does not improve installation safety.
What you get
Report readable for technical and management.
The result is to lead to a decision, rather than ending with a table of numbers. Therefore, each parameter is described in the context of installation operation and costs.
Learn the importance of water parametersWater condition for today
Measurement results with short technical comment, no laboratory jargon.
Named risk
scale, corrosion, biofilm, salinity and energy loss described for your installation.
Specific next step
Correction of dosing, cleaning, passivation, audit or regular monitoring.
Arguments for the Management Board
The report combines technical parameters with impact on operating costs.
From sample to decision
The test result leads to action.
Every stage has a clear goal. This tells us where the sample comes from, what we measure and why we recommend a step.
EntryWater sample and installation description
-
Download
Representative sample →
Sampling
We determine the place of collection and the type of installation so that the result makes technical sense.
-
We measure
Result Set →
Parameter measurement
We test the relevant indicators for boiler, cooling or process water.
-
We interpret
Diagnosis →
Interpretation
We combine numbers with symptoms, installation and operating costs.
-
We recommend
Action Plan →
Recommendation
We convey a clear next step, without excess laboratory jargon.
ResultRecommendation report
Test scope
Parameters are selected for installation.
Otherwise, we read boiler water, or water in the condenser, or else the RO system. The range is determined after talking about installation and symptoms.
-
Response and alkalinity
pH and alkalinity describe the direction of corrosion and stability of the chemical program.
-
Hardness and proneness to sediment
Assessment of the risk of building scale on heat exchange surfaces.
-
Conductivity, TDS and chlorides
Salinity, aggressiveness of water and the basis for setting blowdown and discharges.
-
Iron and Corrosion Products
Signal of sludge transport, corrosion of the installation and condensate dirt.
FAQ
Questions about water analysis.
The sample, the scope of the study, the interpretation of the results and what happens after the report.
How should a sample be collected to obtain a reliable result?
The sample shall be taken from a fixed representative point to a clean vessel and preferably during normal operation of the installation. It is important to describe the place of collection, the date and the working conditions, because without this context the number is difficult to reliably assess.
Which parameters are tested?
The scope depends on the system. We typically test pH, alkalinity, hardness, conductivity, chlorides, TDS and iron. For cooling and RO systems, we add indicators related to deposit, corrosion and microbiological risk.
Is a single analysis sufficient?
A single result shows the condition at a given moment and is usually sufficient for a preliminary diagnosis. However, the evaluation of the effectiveness of the chemical program requires a series of measurements, because it is a trend, not a single reading.
What happens after the results are received?
The results are discussed in the context of the operation of the installation and we indicate the next step: correction of dosing, cleaning, passiveness, technical audit or regular monitoring. We don't leave a client with a table of numbers.
Do I need an in-house laboratory or previous test results?
No. If you do not have current measurements, we perform analysis from scratch. If you have results from another source, we can read them and indicate what is missing for the full image.
Do you have the water results up to date?
Send the parameters. We'll help you read them.
You can also order an analysis if you do not have certain data from recent measurements. Just a brief description of the installation and the symptom.